Sfp 1.25gbps 80km 1550nm

R$199,00

Absolute Maximum Ratings

Table 1 – Absolute Maximum Ratings

 

Parameter	Symbol	Min	Max	Unit
Supply Voltage	Vcc	-0.5	4.5	V
Storage Temperature	Ts	-40	85	°C
Operating Humidity	–	5	85	%

 Recommended Operating Conditions 

Table 2 – Recommended Operating Conditions

  

Parameter		Symbol	Min	Typical	Max	Unit
Operating Case Temperature	Standard	Tc	0		70	°C
	Extended		-20		85	°C
Power Supply Voltage		Vcc	3.13	3.3	3.47	V
Power Supply Current		Icc			300	mA
Data Rate				1.25		Gbps

  

Optical and Electrical Characteristics 

SPT-P151G-80(D): (DFB and PIN, 1550nm, 80km Reach) 

Table 3 – Optical and Electrical Characteristics

  

Parameter		Symbol		Min	Typical	Max	Unit	Notes
Transmitter
Centre Wavelength			λc	1480	1550	1580	nm
Spectral Width (-20dB)			∆λ			1	nm
Side Mode Suppression Ratio			SMSR	30			dB
Average Output Power			Pout	0		5	dBm	1
Extinction Ratio			ER	9			dB
Optical Rise/Fall Time (20%~80%)			tr/tf			0.26	ns
Data Input Swing Differential			VIN	400		1800	mV	2
Input Differential Impedance			ZIN	90	100	110	Ω
TX Disable	Disable			2.0		Vcc	V
	Enable			0		0.8	V
TX Fault	Fault			2.0		Vcc	V
	Normal			0		0.8	V
Receiver
Centre Wavelength			λc	1260		1580	nm
Receiver Sensitivity						-23	dBm	3
Receiver Overload				-3			dBm	3
LOS De-Assert			LOSD			-24	dBm
LOS Assert			LOSA	-30			dBm
LOS Hysteresis				1		4	dB
Data Output Swing Differential			Vout	370		1800	mV	4
LOS			High	2.0		Vcc	V
			Low			0.8	V

  

Notes: 

1. The optical power is launched into SMF.

 2. PECL input, internally AC-coupled and terminated.

 3. Measured with a PRBS 2⁷-1 test pattern @1250Mbps, BER ≤1×10^-12.

 4. Internally AC-coupled.

 

Timing and Electrical 

Table 4 – Timing and Electrical

  

Parameter	Symbol	Min	Typical	Max	Unit
Tx Disable Negate Time	t_on			1	ms
Tx Disable Assert Time	t_off			10	µs
Time To Initialize, including Reset of Tx Fault	t_init			300	ms
Tx Fault Assert Time	t_fault			100	µs
Tx Disable To Reset	t_reset	10			µs
LOS Assert Time	t_loss_on			100	µs
LOS De-assert Time	t_loss_off			100	µs
Serial ID Clock Rate	f_serial_clock			400	KHz
MOD_DEF (0:2)-High	VH	2		Vcc	V
MOD_DEF (0:2)-Low	VL			0.8	V

  

Diagnostics 

Table 5 – Diagnostics Specification

  

Parameter	Range	Unit	Accuracy	Calibration
Temperature	0 to 70	°C	±3°C	Internal / External
	-20 to 85
Voltage	3.0 to 3.6	V	±3%	Internal / External
Bias Current	0 to 100	mA	±10%	Internal / External
TX Power	0 to 5	dBm	±3dB	Internal / External
RX Power	-23 to -3	dBm	±3dB	Internal / External

  

Digital Diagnostic Memory Map 

The transceivers provide serial ID memory contents and diagnostic information about the present operating conditions by the 2-wire serial interface (SCL, SDA). 

The diagnostic information with internal calibration or external calibration all are implemented, including received power monitoring, transmitted power monitoring, bias current monitoring, supply voltage monitoring and temperature monitoring.  

The digital diagnostic memory map specific data field defines as following.

Pin Definitions 

Pin Diagram 

Pin Descriptions

 

Pin	Signal Name	Description	Plug Seq.	Notes
1	VEET	Transmitter Ground	1
2	TX FAULT	Transmitter Fault Indication	3	Note 1
3	TX DISABLE	Transmitter Disable	3	Note 2
4	MOD_DEF(2)	SDA Serial Data Signal	3	Note 3
5	MOD_DEF(1)	SCL Serial Clock Signal	3	Note 3
6	MOD_DEF(0)	TTL Low	3	Note 3
7	Rate Select	Not Connected	3
8	LOS	Loss of Signal	3	Note 4
9	VEER	Receiver ground	1
10	VEER	Receiver ground	1
11	VEER	Receiver ground	1
12	RD-	Inv. Received Data Out	3	Note 5
13	RD	Received Data Out	3	Note 5
14	VEER	Receiver ground	1
15	VCCR	Receiver Power Supply	2
16	VCCT	Transmitter Power Supply	2
17	VEET	Transmitter Ground	1
18	TD	Transmit Data In	3	Note 6
19	TD-	Inv. Transmit Data In	3	Note 6
20	VEET	Transmitter Ground	1

 

Notes: 

Plug Seq.: Pin engagement sequence during hot plugging. 

1) TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc 0.3V. Logic 0 indicates normal operation; Logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V.

 2) TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7k~10kΩ resistor. Its states are:

 Low (0 to 0.8V): Transmitter on

 (>0.8V, < 2.0V): Undefined

 High (2.0 to 3.465V): Transmitter Disabled

 Open: Transmitter Disabled 

3) Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7k~10kΩ resistor on the host board. The pull-up voltage shall be VccT or VccR.

 Mod-Def 0 is grounded by the module to indicate that the module is presente

 Mod-Def 1 is the clock line of two wire serial interface for serial ID

 Mod-Def 2 is the data line of two wire serial interface for serial ID 

 4) LOS is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor. Pull up voltage between 2.0V and Vcc 0.3V. Logic 1 indicates loss of signal; Logic 0 indicates normal operation. In the low state, the output will be pulled to less than 0.8V. 

5) RD-/ : These are the differential receiver outputs. They are internally AC-coupled 100 differential lines which should be terminated with 100Ω (differential) at the user SERDES. 

6) TD-/ : These are the differential transmitter inputs. They are internally AC-coupled, differential lines with 100Ω differential termination inside the module.  

Recommended Interface Circuit

 Mechanical Dimensions